DSP-2
Brady Worldwide Identification Solutions
6555 West Good Hope Road
P.O. Box 2131
Milwaukee, WI 53201-2131
Phone: (800) 537-8791
Fax: (800) 292-2289
05/01
SET-UP INSTRUCTIONS
ADJUSTMENTS
Hold Down Brush:
Place the label roll onto the reel hanger bar. The roll should be against a metal lock clip
so that it is held straight. Place second metal lock clip onto reel hanger bar to keep the
labels snug.
Using the upper thumbscrew on the side of the machine, adjust the hold down brush for
tensioning. For best results, labels should be pressed firmly against the strip plate.
However, if the labels are held too tightly, they will cause excessive drag on the motor.
Thread the web under the guide rod, between the hold down brush and the strip plate
and back under the strip plate. Lay the web across the slot in the take-up hub. Lock the
web in position with the metal lock rod. (The take-up hub turns counter-clockwise.)
Photosensor:
The photosensor can be adjusted in any direction by using the lower thumbscrew on the
side of the machine and the thumbscrew underneath the photosensor bracket. Loosening
the thumbscrew on the side of the machine allows the photosensor to move in and out.
This is used to set the overhang distance of the label over the strip plate. The
Reel Holder Arm
thumbscrew underneath the photosensor bracket is used to swivel the sensor along the
front of the strip plate. When the label is being fed the correct distance, lock the bracket
in place. If there are 2 or more labels across, align the photosensor with the last label to
be removed. When these screws are locked in place, the machine is set.
Positioning of Photosensor
Hold Down Brush
Guide Rod
Lock Rod
Incorrect
Reel Hanger Bar
Strip Plate
Photosensor
Take-up Hub
Sensor sees beyond label
- Will not stop
Sensor sees strip plate
- Will not feed
Daisy-chain option:
Correct
DSP-2 dispensers can be “daisy-chained” together to operate in series. When a label is
removed from one of the machines, the next label will not feed until the labels are
removed from all the machines. Example: If 3 machines are “daisy-chained” together,
when a label is taken off the first machine, it will not feed; when a label is taken off the
second machine, it will not feed. When the label is taken from the third machine, all
machines will feed their respective labels. (DSP-2-CABLE needed to “daisy-chain”
machines.)
Sensor sees front edge of label
4
5
FEATURES
MAINTENANCE
• Will dispense butt-cut and die-cut material.
• Adjustable photosensor for pinpoint accuracy.
• Handled lock rod makes scrap removal easy.
• No tools required for adjustment.
• Turn machine off when not in use.
• Remove liner material from take-up hub when it reaches approximately 2" in
diameter or if the motor appears to be straining.
• Do not operate machine without covers in place.
• Do not operate if inspection reveals a damaged power or sensor cord.
• Keep strip plate, hold down brush and hub free of adhesive build-up.
NOTES
• Keep strip plate free of adhesive build-up.
• Clean photosensor with compressed air or dry cloth.
• Do not drop the dispenser or subject it to heavy shock.
• Turn off machine when not in use.
LEGEND
Model DSP-2
Part #
Item #
1
NV2000-12
NV1000-12-1
NV2000-07
NV1000-07-1
NV2000-08
NV1000-07-1
NV-SPOOL
NV1000-22
NV1000-05
NV1000-05-1
REPAIR POLICY
Contact BRADY CORPORATION to determine nature of problem.
1A
2
2A
3
Furnish Brady with the following information:
1. Who the unit was purchased from.
2. Model number and serial number.
3. Date purchased (copy of invoice or packing slip required).
3A
4
5
6
6A
Brady will issue an RGA (Return Goods Authorization) for repair.
Return machine to Brady by UPS, insured and prepaid.
Brady will notify the customer if there is a repair charge.
7
NV2000-10
NV2000-09
NV1000-09-1
NV1000-18
NV1000-13-1
NV2000-06
NV1000-01-1
NV2000-03
NV1000-13-1
NV1000-03-1
8
8A
9
9A
10
10A
11
11A
11B
SPECIFICATIONS:
Model#
DSP-2
12
NV2000-04
NV2000-02
NV1000-01-1
NV1000-02-1
NV1000-15
NV2000-13/21
NV1000-13-1
NV1000-15-1
NV2000-01
NV2000-11
Liner Capacity
Width
.25" to 2.25"
13
(6.35mm to 57.15mm)
13A
13B
14
Label
25" to 3"
(6.35mm to 76.2mm)
Length
15
15A
15B
16
Roll Capacity
Feed Speed
6" (15.2mm)
2.2" / sec*
(5.6mm / sec.)
17
17A
17B
18
NV1000-11-1
NV1000-01-1
NV1000-16
Dimensions
Inches
Centimeters
7.3 (L) x 4.9 (W) x 9.5 (H)
18.5 (L) x 12.5 (W) x 24.1 (H)
19
NV1000-17
19A
19B
19C
20
21
22
NV1000-17-1
NV1000-17-2
NV1000-17-3
NV1000-19
Weight
2.00 lb. (.91 kg.)
Electrical
12V Dc with 115V adapter
(12V Dc with 220V adapter available)
NV2000-23
Requirements
NV1000-20 (115V)
NV1000-20A (220V)
*speed calculated at 60 Hz
6
3
|