Casio Watch MA0604 EB User Manual

MA0604-EB  
Operation Guide 2993  
About This Manual  
Button operations are indicated using the letters shown  
in the illustration.  
Each section of this manual provides you with the  
information you need to perform operations in each  
mode. Further details and technical information can be  
found in the “Reference” section.  
(Light)  
General Guide  
Press C to change from mode to mode.  
In any mode, press L to illuminate the display.  
Timekeeping Mode  
Stopwatch Mode  
Preset Timer Mode  
Countdown Timer Mode  
World Time Mode  
Alarm Mode  
Press  
.
To toggle between 12-hour and 24-hour timekeeping  
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and  
24-hour timekeeping.  
With the 12-hour format, the P (PM) indicator appears for times in the range of noon  
to 11:59 p.m. and no indicator appears to the left of the hour digits for times in the  
range of midnight to 11:59 a.m.  
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without  
any indicator.  
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is  
applied in all other modes.  
Timekeeping  
Use the Timekeeping Mode to set and view the current  
time and date.  
Month – Day  
Day of week  
Seconds  
Read This Before You Set the Time and Date !  
The times displayed in the Timekeeping Mode and World  
Time Mode are linked. Because of this, make sure you  
select a city code for your Home City (the city where you  
normally use the watch) before you set the time and date.  
For full information on city codes, see the “City Code  
Table”.  
The P indicator is not displayed with the Timekeeping Mode time on the Preset  
Timer Mode, Countdown Timer Mode, World Time Mode, and Alarm Mode screens.  
PM indicator  
Hour : Minutes  
Stopwatch  
The stopwatch lets you measure elapsed time. The upper  
Initial Stopwatch Mode  
display and lower display can be used for official timing of  
Screen  
To set the time and date  
an event or game.  
1. In the Timekeeping Mode, hold down A until the  
seconds start to flash, which indicates the setting  
screen.  
You can configure the watch for beeper alert or vibration  
alert. For details about vibration alert, see “Vibration  
Alert”.  
The measurement range of the upper display is  
59 minutes 59 seconds.  
2. Press C to move the flashing in the sequence shown  
below to select other settings.  
The measurement range of the lower display is  
99 minutes 59 seconds.  
The stopwatch continues to run, restarting from zero  
after it reaches its limit, until you stop it.  
Timekeeping Mode time  
Seconds  
Day  
DST  
City Code  
Year  
Hour  
The stopwatch measurement operation continues even  
if you exit the Stopwatch Mode.  
All of the operations in this section are performed in the  
Stopwatch Mode, which you enter by pressing C.  
Month  
Minutes  
3. When the setting you want to change is flashing, use D and B to change it as  
described below.  
Screen  
50  
To do this:  
Do this:  
Elapsed Time Screen  
Minutes Seconds  
This time measurement (1/100  
second) cannot be paused.  
00  
Reset the seconds to  
Press D.  
Press D.  
Press B to pause and  
restart elapsed time  
measurement.  
ON  
)
OFF  
Toggle between Daylight Saving Time (  
and Standard Time (  
OFF  
)
Change the city code  
Use D (east) and B (west).  
Use D (+) and B (–).  
Minutes Seconds  
This time measurement cannot be  
paused.  
P
10:58  
Change the hour or minutes  
Change the year  
It shows the total elapsed time  
since the timing operation started.  
6-30  
Change the month or day  
See “Daylight Saving Time (DST)” for details about the DST setting.  
4. Press A to exit the setting screen.  
To measure times with the stopwatch  
Elapsed Time  
Hold down  
1
Daylight Saving Time (DST)  
1
Start  
Stop*  
Re-start  
Stop*  
Clear  
Daylight Saving Time (summer time) advances the time setting by one hour from  
Standard Time. Remember that not all countries or even local areas use Daylight  
Saving Time.  
*1 Elapsed time measurement in the lower display continues.  
To toggle the Timekeeping Mode time between DST and Standard Time  
1. In the Timekeeping Mode, hold down A until the  
seconds start to flash, which indicates the setting  
screen.  
Using the Watch for Official Timing of a Sport Event  
After you set a game or event time, the watch will perform an alert operation (beeper  
or vibration) when the time in the lower display reaches that time.  
If the event is interrupted for some reason, you can press B to pause and restart  
timing in the upper display. The lower display shows the total elapsed time since the  
start of the timing operation. You can calculate the total amount of time that play was  
interrupted (lost time or injury time) by subtracting the upper display time from the  
lower display time.  
2. Press C to display the DST setting screen.  
3. Press D to toggle between Daylight Saving Time  
ON  
OFF  
displayed).  
(
displayed) and Standard Time (  
4. Press A to exit the setting screen.  
The DST indicator is on the display while Daylight  
Saving Time is turned on.  
DST indicator  
1
 
Operation Guide 2993  
About the Auto Light Switch  
World Time  
While the auto light switch is enabled, illumination turns on whenever you position  
World Time shows the current time in 48 cities (29 time  
zones) around the world.  
When you enter the World Time Mode, the data you  
were viewing when you last exited the mode appears  
first.  
All of the operations in this section are performed in the  
World Time Mode, which you enter by pressing C.  
your wrist as described below in any mode.  
Timekeeping Mode time  
City code  
Moving the watch to a position that is parallel to the ground and then tilting it  
towards you at more than 40 degrees causes illumination to turn on.  
Wear the watch on the outside of your wrist.  
To view the time for another city code  
In the World Time Mode, press D to scroll eastward  
through city codes or B to scroll westward.  
For full information about city codes, see the City Code  
Table.  
Parallel to ground  
More than 40°  
Current time in the zone  
of the selected city code  
If the current time for a city is wrong, check your  
Timekeeping Mode time and Home city code settings  
and make the necessary changes.  
Warning!  
Always make sure you are in a safe place whenever you are reading the watch  
using the auto light switch. Be especially careful when running or engaged in  
any other activity that can result in accident or injury. Also take care that  
sudden illumination by the auto light switch does not startle or distract others  
around you.  
To toggle a city code time between Standard Time and Daylight Saving Time  
1. In the World Time Mode, use D and B to display the  
city code (time zone) whose Standard Time/Daylight  
Saving Time setting you want to change.  
When you are wearing the watch, make sure that its auto light switch is turned  
off before riding on a bicycle or operating a motorcycle or any other motor  
vehicle. Sudden and unintended operation of the auto light switch can create  
a distraction, which can result in a traffic accident and serious personal injury.  
2. Hold down A for about one second to toggle between  
Daylight Saving Time (DST displayed) and Standard  
Time (DST not displayed).  
To turn the auto light switch on and off  
The DST indicator is on the display whenever you  
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto  
light switch on (A.EL displayed) or off (A.EL not displayed).  
The auto light switch indicator is on the display in all modes while the auto light  
switch is turned on.  
display a city code for which Daylight Saving Time is  
turned on.  
DST indicator  
Note that the DST/Standard Time setting affects only  
the currently displayed city code. Other city codes are  
not affected.  
In order to protect against running down the battery, the auto light switch turns off  
automatically approximately six hours after you turn it on.  
Alarm  
Reference  
When the Daily Alarm is turned on, the currently selected  
alert operation (beeper or vibration) is performed at the  
preset time each day. When the Hourly Time Signal is  
turned on, the watch performs an alert operation every  
hour on the hour.  
You can configure the watch for beeper alert or vibration  
alert. For details about vibration alert, see Vibration  
Alert.  
This section contains more detailed and technical information about watch operation.  
It also contains important precautions and notes about the various features and  
functions of this watch.  
Hourly time signal  
on indicator  
Timekeeping  
Mode time  
Vibration Alert  
When Vibration Alert is turned on, the watch vibrates instead of sounding a beeper.  
This lets you use the watch without disturbing others with beeping sounds.  
Vibration Alert can be used to replace alarm sounds.  
For information about selecting the alert type, see To switch between vibration alert  
and beeper alertbelow.  
All of the operations in this section are performed in the  
Alarm Mode, which you enter by pressing C.  
To set the alarm time  
Watches with a metal band may produce a noise when a vibration operation is  
performed. This is due to vibration of the metal band, and does not indicate  
malfunction of the watch.  
Alarm time  
(Hour : Minutes)  
1. Hold down A while in the Alarm Mode until the hour  
setting of the alarm time starts to flash, which indicates  
the setting screen.  
Alarm on indicator  
This operation turns on the alarm automatically.  
To switch between vibration alert and beeper alert  
In any mode, press V to toggle the alert operation  
between vibration (VIB displayed) and beeper (VIB not  
displayed).  
2. Press C to move the flashing between the hour and minute settings.  
3. While a setting is flashing, use D (+) and B () to change it.  
4. After you set the alarm time, press A to exit the setting screen.  
With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).  
To stop the alarm tone after it starts to sound  
Press any button.  
To switch the Daily Alarm and Hourly Time Signal on and off  
Press D while in the Alarm Mode to change the status of the Daily Alarm and Hourly  
Time Signal in the following sequence.  
Vibration alert indicator  
Scrolling  
The B and D buttons are used in various modes and setting screens to scroll  
through data on the display. In most cases, holding down these buttons during a scroll  
operation scrolls at high speed. This is true except when the countdown timer number  
is flashing on the Countdown Timer Mode screen.  
Both on  
Both off  
Daily Alarm  
only  
Hourly Time  
Signal only  
Auto Return Features  
If you leave the watch in the Alarm Mode for two or three minutes without performing  
any operation, it changes to the Timekeeping Mode automatically.  
If you leave a screen with flashing digits on the display for two or three minutes  
without performing any operation, the watch exits the setting screen automatically.  
To test the alert operation  
In the Alarm Mode, hold down D to perform the currently selected alert operation  
(beeper or vibration).  
Timekeeping  
Illumination  
00  
Resetting the seconds to  
while the current count is in the range of 30 to 59  
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are  
This watch has an EL (electro-luminescent) panel that  
causes the entire display to glow for easy reading in the  
dark. The watchs auto light switch turns on illumination  
automatically when you angle the watch towards your  
face for reading.  
The auto light switch must be turned on (indicated by  
the auto light switch indicator) for it to operate.  
See Illumination Precautionsfor more important  
information.  
00  
reset to  
without changing the minutes.  
The year can be set in the range of 2000 to 2099.  
The watchs built-in full automatic calendar makes allowances for different month  
lengths and leap years. Once you set the date, there should be no reason to change  
it except after you have the watchs battery replaced.  
World Time  
The seconds count of the World Time is synchronized with the seconds count of the  
Timekeeping Mode.  
All World Time Mode times are calculated from the current Home City time in the  
Timekeeping Mode using UTC time differential values.  
Auto light switch indicator  
The UTC differential is a value that indicates the time difference between a  
reference point in Greenwich, England and the time zone where a city is located.  
The letters UTCis the abbreviation for Universal Time Coordinated, which is the  
world-wide scientific standard of timekeeping. It is based upon carefully maintained  
atomic (cesium) clocks that keep time accurately to within microseconds. Leap  
seconds are added or subtracted as necessary to keep UTC in sync with the Earths  
rotation.  
To illuminate the display manually  
In any mode, press L to turn on illumination for about one second.  
The above operation turns on illumination regardless of the current auto light switch  
setting.  
3
 
Operation Guide 2993  
Illumination Precautions  
The electro-luminescent panel that provides illumination loses power after very long  
use.  
Illumination may be hard to see when viewed under direct sunlight.  
The watch may emit an audible sound whenever the display is illuminated. This is  
due to vibration of the EL panel used for illumination, and does not indicate  
malfunction.  
Illumination turns off automatically whenever an alert operation (beeper or vibration)  
is performed.  
Frequent use of illumination runs down the battery.  
Auto light switch precautions  
Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light  
switch to operate when it is not needed, which shortens battery life. If you want to  
wear the watch on the inside of your wrist, turn off the auto light switch feature.  
Illumination may not turn on if the face of the watch is  
more than 15 degrees above or below parallel. Make  
sure that the back of your hand is parallel to the ground.  
Illumination turns off in about one second, even if you  
keep the watch pointed towards your face.  
Static electricity or magnetic force can interfere with proper operation of the auto  
light switch. If illumination does not turn on, try moving the watch back to the starting  
position (parallel with the ground) and then tilt it back towards you again. If this does  
not work, drop your arm all the way down so it hangs at your side, and then bring it  
back up again.  
Under certain conditions, illumination may not turn on until about one second after  
you turn the face of the watch towards you. This does not necessarily indicate  
malfunction of the auto light switch.  
You may notice a very faint clicking sound coming from the watch when it is shaken  
back and forth. This sound is caused by mechanical operation of the auto light  
switch, and does not indicate a problem with the watch.  
City Code Table  
City  
Code  
UTC  
Differential  
City  
Other major cities in same time zone  
PPG  
HNL  
ANC  
YVR  
Pago Pago  
Honolulu  
Anchorage  
Vancouver  
11.0  
10.0  
09.0  
08.0  
Papeete  
Nome  
Las Vegas, Seattle/Tacoma, Dawson City  
SFO San Francisco  
LAX  
DEN  
MEX  
CHI  
Los Angeles  
Denver  
Mexico City  
Chicago  
07.0  
06.0  
El Paso, Edmonton  
Winnipeg, Houston, Dallas/Fort Worth, New Orleans  
MIA  
Miami  
05.0  
Montreal, Detroit, Boston, Panama City, Havana, Lima,  
Bogota  
La Paz, Santiago, Port Of Spain  
NYC  
CCS  
YYT  
New York  
Caracas  
St. Johns  
04.0  
03.5  
03.0  
01.0  
+00.0  
RIO Rio De Janeiro  
RAI  
LIS  
LON  
BCN  
PAR  
MIL  
ROM  
BER  
ATH  
Sao Paulo, Buenos Aires, Brasilia, Montevideo  
Dublin, Casablanca, Dakar, Abidjan  
Praia  
Lisbon  
London  
Barcelona  
Paris  
Milan  
Rome  
Berlin  
Athens  
+01.0  
+02.0  
+03.0  
Amsterdam, Algiers, Hamburg, Frankfurt, Vienna,  
Stockholm, Madrid  
Helsinki, Beirut, Damascus, Cape Town  
JNB Johannesburg  
IST  
CAI  
Istanbul  
Cairo  
Jerusalem  
Moscow  
Jeddah  
Tehran  
Dubai  
Kabul  
Karachi  
Male  
Delhi  
JRS  
MOW  
JED  
THR  
DXB  
KBL  
KHI  
MLE  
DEL  
DAC  
RGN  
BKK  
SIN  
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi  
+03.5  
+04.0  
+04.5  
+05.0  
Shiraz  
Abu Dhabi, Muscat  
+05.5  
+06.0  
+06.5  
+07.0  
+08.0  
Mumbai, Kolkata  
Colombo  
Dhaka  
Yangon  
Bangkok  
Singapore  
Hong Kong  
Beijing  
Jakarta, Phnom Penh, Hanoi, Vientiane  
Kuala Lumpur, Taipei, Manila, Perth, Ulaanbaatar  
HKG  
BJS  
SEL  
TYO  
ADL  
GUM  
SYD  
NOU  
WLG  
Seoul  
Tokyo  
+09.0  
Pyongyang  
Adelaide  
Guam  
Sydney  
Noumea  
Wellington  
+09.5  
+10.0  
Darwin  
Melbourne, Rabaul  
+11.0  
+12.0  
Port Vila  
Christchurch, Nadi, Nauru Island  
*Based on data as of June 2005.  
4
 

Beyerdynamic Power Supply MCS 20 User Manual
Black Decker Fan FB1400 User Manual
Bosch Appliances Clothes Dryer WTB86202UC 01 User Manual
Bosch Appliances Range HGS3023UC User Manual
Boston Acoustics Speaker VRiSub82 User Manual
Canon Digital Camera ST E3 RT User Manual
Casio Car Video System QT 6100 User Manual
Casio Digital Camera EX Z1 User Manual
CBM America Printer CBM 1000II User Manual
Cecilware Oven BK 44 User Manual